Painting Project Preparation Tips: The Prep Work That Makes Paint Last

By Fast Guys Remodeling

Good painting project preparation means cleaning the surface, repairing damage, sanding, caulking, priming stains and protecting everything you do not want painted, before the first coat. Paint cannot hide dirt, glossy sheen or loose patches. Prep is often most of the job, and it decides whether the finish lasts.

Illustration of a painter pressing spackle into a crack on a wall

Painting prep work checklist at a glance

  • Clear the room or push furniture to the center and cover it
  • Lay drop cloths and protect floors and fixtures
  • Remove switch plates, outlet covers, hardware and wall hangings
  • Wash walls and trim, rinse and let dry
  • Fill holes and cracks, then sand the repairs smooth
  • Re-caulk gaps at trim, tub, windows and corners
  • Scuff-sand glossy surfaces
  • Spot-prime patches, stains and bare wood
  • Mask edges with painter's tape
  • Check ventilation, temperature and lighting before you start

Step 1: Clear the room and protect what stays

Move small furniture out and push the rest to the center of the room, covered with plastic or cloth. Cover floors with drop cloths. Plastic sheeting alone is slippery, so use canvas or paper under the work area. Remove switch plates, outlet covers, curtain rods and wall hangings and keep the screws in a labeled bag.

Step 2: Clean and degrease the surfaces

Paint sticks to clean surfaces. Wash walls with warm water and a mild detergent, using a sponge or cloth. Rinse with clean water to remove soap residue and let the walls dry completely. Kitchens and bathrooms need extra attention because grease and moisture build up there. Dust ceiling corners and trim tops before you wash, so dirty water does not run down clean walls.

Step 3: Repair holes, cracks and dents

Fill small holes and hairline cracks with spackle or joint compound and let it dry. Larger holes need backing or a drywall patch before compound goes on. Apply thin coats, since thick coats shrink and crack. Sand each repair smooth once it is dry. For bigger damage, see drywall repair and installation.

Step 4: Caulk the gaps

Use paintable caulk where trim meets walls and where walls meet ceilings. Use a mildew-resistant caulk around tubs and sinks. Smooth the bead with a damp finger or tool and let it cure before painting.

Step 5: Sand for adhesion and a smooth finish

Sanding removes flaking paint, smooths repairs and dulls glossy surfaces so new paint grips. For walls, fine-grit sandpaper in the 120 to 220 range is typical. Wipe dust away with a damp cloth or a tack cloth.

Step 6: Prime where it is needed

Primer seals the surface and helps paint stick evenly. Prime new drywall, bare wood, fresh patches, stains and any surface you are changing dramatically in color. A stain-blocking primer keeps water, smoke and marker stains from bleeding through. Let primer dry fully before painting.

Step 7: Mask edges and check the conditions

Apply painter's tape to trim, windows and the ceiling line, and press the edge down to prevent bleed. Open windows or run fans for ventilation. Check the label for temperature and drying times. Use good light, ideally from a window and a work lamp held at an angle, so you can spot missed spots before the paint goes on.

Illustration of a painter taping edges and covering the floor before painting

Tools and materials for interior painting prep

  • Drop cloths, painter's tape and plastic sheeting
  • Mild detergent, sponge and clean rags
  • Spackle or joint compound, putty knife, and drywall patch kits
  • Sandpaper or a sanding block, plus a tack cloth
  • Paintable caulk and a caulk gun
  • Primer, including a stain-blocking type for water or smoke stains
  • Screwdriver and a labeled bag for hardware
  • Ladder, work light and a respirator or dust mask for sanding

Surface notes: what changes for different walls

SurfaceWhat to do
New drywallPrime before paint; new board and joint compound absorb paint differently
Glossy trim and doorsClean, scuff-sand, then use a bonding primer
KitchensDegrease walls and trim near the stove before anything else
BathroomsCheck for mildew, fix ventilation, use mildew-resistant caulk and a moisture-resistant paint
Water stainsFind and stop the leak, let the area dry, then use a stain-blocking primer. See bathroom moisture problems
Bare woodSand smooth, wipe clean and prime

Common painting prep mistakes

  • Painting over dirty or greasy walls
  • Skipping repairs, so cracks and holes show through the paint
  • Not sanding glossy surfaces
  • Priming too little, or not at all, over stains and patches
  • Taping over damp or dusty surfaces, so the tape does not hold
  • Skipping floor and fixture protection
  • Painting before the last coat of primer or caulk has dried

Older homes: lead-safe prep

Homes built before 1978 may contain lead-based paint. Federal rules (the EPA's Renovation, Repair and Painting rule) require lead-safe work practices for paid renovation in most pre-1978 homes. Ask any contractor for their EPA lead-safe certification before work starts. Do not dry-sand or scrape old paint in a pre-1978 home without lead-safe precautions.

Source: U.S. EPA, Lead Renovation, Repair and Painting Program (epa.gov/lead/renovation-repair-and-painting-program).

How long does painting prep take?

Prep often takes as long as the painting itself, and sometimes longer. A room with a few holes and clean walls may need an afternoon. A room with repairs, caulk, stains and glossy trim can take a couple of days because patches, caulk and primer need time to dry. Plan your schedule around drying times, not just working time.

When to hand prep and painting to a pro

Call a painter when the room has repairs beyond small holes, high ceilings, lead concerns, a whole-house schedule or trim that needs extra care. Prep and painting by the same company also keeps the work coordinated. See interior painting for how that works. If you are weighing paint against a bigger job, read interior painting vs. a full remodel. Painting the outside instead? Start with how to prepare your exterior for paint in Kansas City weather.

Frequently asked questions

Do I need to prime before painting?

Often yes. Prime new drywall, bare wood, fresh patches, stains and any wall where you are changing color dramatically. You may not need primer on clean, sound walls painted in a similar color, but spot-priming patches still helps the finish look even.

Do I need to sand between coats?

Not usually between coats of wall paint. Sand before painting to smooth patches and dull glossy surfaces. Sand lightly between coats only when the finish feels rough or you are working with certain trim finishes, and wipe away dust afterward.

How long should I wait between prep steps and painting?

Wait until each step is dry to the touch and ready to be sanded or coated. Joint compound, caulk and primer each have their own drying times on the label. Rushing causes cracks, bubbles and peeling. When the weather is humid, allow extra time.

Can I paint over wallpaper or glossy paint?

Glossy paint needs cleaning, scuff-sanding and a bonding primer. Wallpaper is often better removed, because moisture from paint can loosen it. If it must stay, it must be tight and clean, and test a small area first.

How do I handle a water stain before painting?

Find and fix the source of the moisture first. Let the area dry, check the board is solid, then use a stain-blocking primer before the topcoat. Painting over an active leak only hides the problem for a short time.

More on this topic: Interior painting · More remodeling guides

Related guides

Recent posts

Have a repair or finish job in mind?

Describe the damage or the rooms. Photos help when you call or write.

CallGet a Quote